4WD RC Buggy - Orange

FOLLOWERS

748

LIKES

Greyhound - 4WD RC Buggy with BuWizz 2

First of all, a big thank you to everybody who supported me in the corresponding WIP-topic on Eurobricks!

Update
2019/03/15 - I improved the way the rims are connected to the turn-tables and updated the instructions accordingly. I made MOD-instructions in case you would want to upgrade your existing build with these changes: https://photos.app.goo.gl/nAw92pxpnCykSkSj8



2018/12/08 - During rough rides the first and only link that can disconnect are the pins with towball that connect the gearrack assembly to the steering links. If you want to take this model to the limit, it's advisable to use set-screws to secure the pins. Drive the screws all the way in. They should surpass the outer ridges of the pin:



Background
Apart from pursuing performance, this model explores what's possible when it comes to robustness and durability. This has much to do with the fact that this is a 4WD model with 2 BuWizzes. A lot of power is sent to both the front and the rear wheels. That puts high demands on the strength of all kind of things; the steering, the suspension, the chassis, the bodywork. I had to think outside the beaten track on all these aspects, while holding on to requirements such as Ackermann geometry, small turning radius, extensive suspension travel and minimal slack in moving parts. But adding strength and coherence comes at the price of using more parts, which adds weight, which requires even more strength, etc. With this model I have tried to find a balance between performance, robustness and weight. A balance that fits the power of 2 BuWizzes and 4L motors on the one hand and a 4WD model built from LEGO on the other hand.

Important
-Pages 163, 169, 303, 304, 349 and 350 show the results of obsolete steps. They are made transparent and have a red cross at the bottom-right corner. They only serve to inform you about some additions that should be ignored in further steps. The replacement steps are at the end of the instructions, starting from page 703.
-In the instructions replace all white and medium blue parts by orange parts, except for the white center stripe in the bodywork and in the center column. Also replace the two black small panels at the back of the roof with orange ones.
-If you want the BuWizzes to be removable more easily, remove the red pins holding them, after page 532.
-To avoid wear and improve performance, it is advisable to lubricate the springs and the turn-tables. Use PTFE spray from WD40 (so NOT the normal WD40 spray). The impact modifier in ABS dissolves in the silicon carrier in silicon spray. WD40 PTFE spray does not have this issue.
-Try to keep your turn-tables clean.
-2 BuWizzes are not included in the inventory.

Features
-Turn-table-based wheel-hubs with minimal slack
-4WD by means of 4 L-motors powered by two BuWizz 2 units
-Fully independent suspension
-Steering with Servo-motor
-30 degree steering angle with Ackermann geometry
-Caster angle
-Fake V8-engine driven by M-motor
-Can handle a rough ride
-Liftable by roof, nose and tail
-Everything in-system

Notes on parts
- 99773 (Technic Beam Triangle Thin [Type II]) used inside the front suspension module should not be confused with 2905 (Technic Beam Triangle Thin [Type I]).
- 95292c01 (Technic Shock Absorber 9.5L with Extra Hard Springs) are quite expensive. You might consider assembling them yourself from the cheaper 2909c03 (Technic Shock Absorber 9.5L with Soft Springs) and non-LEGO springs. On doctor-brick.de the following springs have been suggested:



Some indoor playing...

Buy this MOC

Want to buy this MOC to build? You'll need to buy the parts and the building instructions using the tabs below.
Login to hide ads!

MOC-19664

Name 4WD RC Buggy - Orange
Designer Didumos
Designed 2018
Parts 1912
Theme Technic
Already have some of the parts? Use the Build this MOC page to only show the parts you are missing.
Create an account to change the default filters used.

Waiting for Inventory to load

Instructions:
PDF - Photo Sequence
Cost:

Please Log In

Sorry, but you need to be logged in to buy these instructions so that you can download them again at any time. Login or quickly signup using the form below.

You might like these other similar Premium MOCs

4WD RC Buggy

By Didumos
MOC-19517
(1912 parts)

Custom RC Dump Truck

MOC-8002
(1805 parts)
Help Guide - BI File Types

This MOC also has a 3D digital file available (eg LDD, MPD, etc): 3D Model

Submitted by mechanics Jan. 25, 2019
Submitted by mechanics Jan. 25, 2019
Submitted by mechanics Jan. 25, 2019
Submitted by mechanics Jan. 25, 2019
Submitted by mechanics Jan. 25, 2019
Submitted by mechanics Jan. 25, 2019
Submitted by mechanics Jan. 25, 2019
Submitted by MultiDoc Nov. 30, 2018
Submitted by MultiDoc Nov. 30, 2018
Submitted by MultiDoc Nov. 30, 2018
Submitted by MultiDoc Nov. 30, 2018
Submitted by MultiDoc Nov. 30, 2018
Submitted by MultiDoc Nov. 30, 2018